Shiplap Calculator & Wall Planner

Enter your wall, board width and gap, and choose horizontal or vertical. You get a board count with staggered seams, a cut list around windows and doors, nails and adhesive, and a live drawing to scale. Free, no sign-up.

Live preview

drawn to scale, seams staggered
–rows
–last board rip
–gap
–boards to buy

Your wall

Wall size
ftin
mm
ftin
mm
in

Leave baseboard at 0 to run boards to the floor (then reinstall a cap over the shiplap). Set it to the existing base height to start the first course on top. Fractions are fine: 5 1/2, 8 ft.

Orientation
Boards & gap
in
in
in

Reveal is the face you see. A 1x6 is 5 1/2" actual; a 1x8 is 7 1/4". For nickeled 1x boards that is also the board width; for rabbeted shiplap, enter the visible face after the overlap. Size: Gap: Length:

in

Offset on alternate rows. Half the board length (often 48") is typical so joints land on a stud.

Fit at the last board

Rip last is the usual install. Split shares a thin leftover top and bottom. Even gaps nudges the spacing so every board stays full width.

Windows, doors & outlets

Position = left edge of the opening from the left wall edge, and bottom from the floor. Include the casing/trim in the size.

Waste & cuts
%
in

10–15% extra covers miscuts and damaged boards. Kerf is taken when packing pieces onto a stock board.

Results & cut list

Cut list

PieceLengthQtyNotes

Packing uses first-fit on the cut list with your saw kerf. Ripped starter or cap boards still come from the same full-width stock. Extra % is added on top for miscuts and bad boards. Nail counts assume two 18-gauge brads at each 16" station; adhesive assumes about 30 linear feet per 10 oz tube. These are planning estimates only.

How to plan a shiplap wall

Shiplap is a wall of boards with a small, even shadow line between them. The look comes from two numbers: the exposed width of each board (the reveal) and the gap you leave between courses. Get those consistent, stagger the end joints, and work cleanly around windows, and the wall looks built-in. The planner above does the arithmetic; this guide covers the decisions behind it.

1. Measure the wall properly

Measure the width and height in more than one place and use the smallest numbers – walls are rarely square. If you will leave the existing baseboard, start the first course on top of it; if you will run boards to the floor, set the baseboard field to zero and reinstall a cap later. Measure every window and door to the outside of the casing, and mark outlets and switches – those openings are subtracted from the board count and show up as cuts on the preview.

2. Pick a board size

The reveal you enter is the face you will see. For nickeled 1x boards (square-edge boards with a spacer – the most common DIY “shiplap”) that is the actual board width. For true rabbeted shiplap it is the visible face after the overlap.

NominalActual widthGood for
1x43 1/2"Small rooms and a tighter pattern
1x65 1/2"The default for most interior accent walls
1x87 1/4"Large rooms and tall ceilings
1x109 1/4"Wide, rustic or cottage walls

Primed finger-jointed pine and pre-primed MDF both paint well and come in 8-, 12- and 16-foot lengths. Use PVC or a moisture-resistant product in a bathroom. Longer stock means fewer end joints, if the boards fit in your vehicle.

3. Choose a gap and plan the last board

A nickel gap – about 5/64 inch – is the usual painted look and leaves a little room for seasonal movement. A 1/16 inch gap is tighter; 1/8 inch makes a stronger shadow line. True rabbeted shiplap can be installed tight, because the overlap hides movement. Keep the gap consistent with a spacer or a nickel.

The last course almost never lands on a full board, so you rip it to the leftover height. If that rip would be a sliver under about 1 1/2 inches, switch the planner to “split first & last” so the leftover is shared top and bottom, or use “even gaps” to nudge the spacing so every board stays full width:

courses = ceil( (wall height + gap) ÷ (reveal + gap) )
last board = wall height − (courses − 1) × (reveal + gap)

Example: an 8 ft (96") wall with 1x6 boards (5 1/2") and a 1/8" gap has a 5 5/8" pitch, 18 courses, and a last board of only 3/8" – a sliver worth splitting or avoiding by adjusting the gap.

4. Horizontal or vertical

Horizontal shiplap is the classic look and is usually faster, because you can keep one level line and work up the wall. Vertical shiplap can make a low ceiling feel taller and suits a narrow accent. In either direction the first course has to be dead straight – a laser or a snapped chalk line – because every later board will copy any error.

5. Stagger the seams and work around openings

An 8-foot board will not span a 12-foot wall, so you will have end joints. Do not stack those joints in a column; they read as a zipper and they are weaker. Start every other course with a half board (or a 32- or 48-inch starter) so the seams fall on a stud and miss the seam below by at least 16 to 24 inches. The preview draws that stagger before you cut.

Around a window or door, run the boards into the casing and cut them to fit; do not carry one board across an opening. For outlets, cut the opening in the board and use a box extender so the device sits flush with the new face. Turn the circuit off before you remove a cover plate.

6. How many boards, nails and adhesive to buy

Add up every piece on the cut list, pack those lengths into your stock, then add 10 to 15 percent for miscuts, dented edges and the ripped starter or cap. The planner also estimates 18-gauge brads (two at each 16-inch station) and construction adhesive at about one 10-ounce tube per 30 linear feet. Those are planning numbers, not a promise.

A bead of construction adhesive plus 2-inch 18-gauge brads holds painted interior shiplap to drywall. Fill the nail holes, caulk where boards meet the casing, and finish with primer plus two top coats in satin or semi-gloss so the shadow lines stay sharp.

Common mistakes to avoid

Shiplap planning FAQ

What size boards should I use for an interior shiplap wall?

Most interior accent walls use 1x6 boards, which are 5 1/2 inches actual width. 1x8 (7 1/4 inches) suits a large room or a tall ceiling, and 1x4 (3 1/2 inches) suits a small room. Enter the exposed reveal – the face you will see – which is the actual board width for nickeled 1x boards, or the visible face after the overlap on true rabbeted shiplap.

How big should the gap between shiplap boards be?

A nickel gap, about 5/64 inch, is the usual painted look and leaves a little room for seasonal movement. A 1/16 inch gap is tighter; 1/8 inch makes a stronger shadow line. True rabbeted shiplap can be installed tight (a zero gap) because the overlap hides movement. Keep the gap consistent with a spacer block or a nickel.

How do I calculate how many shiplap boards to buy?

Divide the wall height (or width, for vertical shiplap) by the board reveal plus the gap to get the number of courses, rip the last board to fit, then pack the cut lengths into your stock board length and add 10 to 15 percent for waste. Subtract window and door openings from the linear footage. The planner above does this and shows a cut list.

Should I install shiplap horizontal or vertical?

Horizontal shiplap is the classic look and is usually faster because you can keep one level line and work up the wall. Vertical shiplap can make a low ceiling feel taller and suits a narrow accent. In either direction the first course has to be dead straight, because every later board will copy any error.

How should I stagger the end joints on a shiplap wall?

Do not stack end joints in a straight column. Start every other course with a half board, or a 32- or 48-inch starter, so each seam lands on a stud and misses the seam in the course below by at least 16 to 24 inches. The planner draws that stagger on the live preview.

What do I do with the last board at the ceiling?

The last course almost never lands on a full board, so you rip it to the remaining height. If that rip would be a sliver under about 1 1/2 inches, split the leftover between the first and last courses, or slightly adjust the gap so every board stays full width. The planner offers all three options.

More wall planning tools

Estimates are for planning only. Always verify measurements on site and follow local electrical codes.